Showing results: 631 - 645 of 984 items found.
-
Model TTPX -
Lake Shore Cryotronics, Inc.
The Model TTPX is a versatile cryogenic micromanipulated probe station used for non-destructive testing of devices on full and partial wafers up to 51 mm (2 in) in diameter.
-
Model FWPX -
Lake Shore Cryotronics, Inc.
The Model FWPX is a versatile cryogenic micro-manipulated probe station used for nondestructive testing of devices on full and partial wafers up to 102 mm (4 in) in diameter.
-
MTI Corp.
economic nail penetration tester for all types of rechargeable batteries, which meets CE standard. The nail penetration is performed inside a safe and vented stainless-steel test chamber using a 3~8 mm diameter steel nail at variable speed from 10~100mm/s. There is a fixture to tighten various type cells, pouches or cylinders in the test chamber.
-
infraTest Prüftechnik GmbH
Stand model in four-pillar design with electronic force transducer, flanged to the movable testing machine crosshead and electronic position transducer for measuring the crosshead path. The machine is driven by a quartz-precise stepper motor with two ball screws. Complete with integrated displacement measuring device 0.01 mm over the entire travel distance as well as additional displacement transducer with connecting cable and holder
-
Idex Health and Science
IDEX Health & Science stocks filter cubes used in fluorescence microscope platforms from the major microscope manufacturers, including Leica Microsystems, Nikon Instruments, Olympus Corp., and Zeiss Microscopy. Our super-resolution filter cubes set the new standard for laser-based microscopes and are optimized for mounting half-wave flatness, 1 mm thick super-resolution dichroic beam-splitters. Whether you order a custom or catalog filter set, complimentary filter mounting into the filter cube of your choice is performed by the certified staff.
-
E1834M -
Keysight Technologies
The E1834M is a beam bender that bends the incoming beam at a 90-degree angle and is designed for beam diameters of 9 mm or less. This referenced optics uses high performance horizontal mount to deliver laser beam throughout a measurement system. The 8 flexure feet are designed for stable beam pointing.
-
-
-
CX-104 -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one
-
CX-12.5 -
Shenzhen Chuangxin Instruments Co., Ltd.
The rigid sphere (12.5 mm) from Autostrong is designed and manufactured to perform the test specified in many standards (IEC 60335, IEC 60065, IEC 60745, IEC 61029, IEC 60950) to prove the degree of protection for the first characteristic numerals 2 (IP2X) .Its is designed to meet the requirements of international safety regulatory agencies such as UL, DNV, IMQ, BVSQ, ITS, IRAM , CSA, VDE, DIN , INMETRO.
-
CX-RIP3/4 -
Shenzhen Chuangxin Instruments Co., Ltd.
For checking the protection against water with spray nozzle of 0,4 mm bore are used to prove the degrees of protection for the second characteristic numerals 3 and 4 “Protection against Spraying Water” resp. “Protection against splashing Water”.
-
CX-18 -
Shenzhen Chuangxin Instruments Co., Ltd.
Wire and cable slicing machine is a kind of used products factory la bequipment. Using mechanical transmission feed, blade cutting structure, it can be cut1 to 12 mm range plastic various thickness, sheet material, etc., they are availablRubber, leather material and hardness of the material must be sliced, the machine is widelyUsed in rubber, plastic, leather, electric wire, cable, scientific research units, etc.
-
CX-GZ -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 103 Vessel for testing hotplatesParameter:1.Pot and lid material industrial aluminum2. Pot material thickness 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm;4. Pot body and lid surface should be smooth;5, size: 110, 145, 180, 220, 300mm each one
-
-
Duma Optronics LTD
Modern laser applications seldom require large beam profiling, combined with high resolution. The BeamOn HR 1" is the perfect solution enabling both relatively large beam characterization, with a high resolution detector of 20 MP. By implementing a diffuser to present the beam to a smaller detector via dedicated optics, one of the largest beam profilers of 60 mm is offered, i.e BeamOn LA U3. Even further than that, for collimated beams the Laser Analyzing Telescope offers an input aperture of 100 mm combined with high resolution, attitude and divergence measurement of the laser beam.